FILTER SISTEM

Detil Produk :

FLO KING FILTER SYSTEMS

INTRODUCTION TO FLO KING FOUR IN ONE SYSTEMS

Flo King in-tank technology for the metal finishing industry is a radical departure from conventional
approaches. Traditionally, metal finishers have relied on out-of-tank systems, which use a tube or hose
to draw solution outside the tank and “push” it through a filter cartridge or series of cartridges in a filter
chamber. Leaks and spills due to corroded plumbing, loose clamps, leaky seals, etc., are commonplace.
Flo King eliminates those and many other concerns.
• Lightweight, in-tank Flo King systems provide flow rates of hundreds and even thousands of gallons
per hour and can be stationed permanently on one tank or moved from one tank to another as needed.
• Since they employ no hoses, clamps, tubes, plumbing, filter chambers or any external apparatus, Flo
King systems eliminate the possibility of leaks and spills. Solution never leaves the tank.
• Flo King systems are supplied complete, preassembled, and ready to operate, with no costly
installation or floorspace required. Yet they take up only inches of in-tank space.
• Flo King filter changes are achieved quickly, without tools.
• Flo King systems can PUMP solution from one tank to another, FILTER in a variety of configurations,
AGITATE to promote uniform chemical composition and temperature, and TREAT using carbon for the
removal of organic impurities. That’s why we call it the “four-in-one system.”

HOW IT WORKS
With vacuum-side, in-tank Flo King filtration, one or more filter cartridges are totally immersed in the
tank and solution to be filtered. Solution is then “pulled” by vacuum through the cartridge(s), after which
it travels a few short inches before being expelled from a directable discharge port on the pump body.
As this filtered solution is discharged at a high rate, agitation and solution circulation are achieved as
a natural byproduct of filtration.
The Flo King system can be used with high-quality disposable or reusable
filter cartridges. When dirty, the reusable blanket-like material is unrolled
from the cartridge core. Many users then lay the material on a piece of metal
or plastic grating over a suitable tank, drum or other reservoir and spray it
clean using an ordinary hose and spray nozzle (or pressure washer, if
available). While still wet, the blanket can be rerolled around the core (also
reusable) and reused many times. The Flo King system is also readily used
with carbon-containing attachments to remove organic impurities—in the
tank, without messy, expensive, time-consuming batch treatment in a
separate tank.
Vacuum-side Flo King filtration provides another important benefit:
particulate penetration deep inside the filter media. With conventional
pressure-side filtration, solution is essentially “pushed” through a filter
cartridge. But with each and every Flo King system, solution is “pulled”
through the cartridge by vacuum, providing particulate penetration and
retention deep inside the filter media where the filter fibers are more densely
packed. That translates to very fine filtration!
(Agitator)

Detil Produk :

FLO KING BX1200 Filter System

The FLO KING BX1200 provides a maximum flow rate of 1200 gallons (4500 liters) per hour. Use it stationary on one tank or move it from tank to tank. Multiple body lengths (4, 6, 8, 10, 12, and 14 inch) enable use of the BX1200 in tanks with varying solution levels and depths.
   The BX1200 comes complete, preassembled, ready to operate and includes the items shown in the labeled photo below. For best results in most metal-finishing solutions, use the BX1200 with our Permacore Magnum Reusable or Poly-Spun Disposable filter cartridges in the appropriate length.

BX1200 Specifications
Pump: Available in CPVC, polypropylene, PVDF (Kynar), and stainless steel as pump materials of construction. Standard shaft is 303 stainless steel covered with Teflon heat-shrink tubing. As a precaution for aggressive solutions that may attack SS, a titanium shaft is available for pump-body lengths of 6, 8, 10, & 12 inches and a Hastelloy-C276-alloy shaft is available for pump-body lengths of 6, 8, 10, 12 & 14 inches.
Flow Rate: 1200 gallons (4500 liters) per hour at 60 Hz. A flow-rate reduction of about 18% is typical when operating at 50 Hz.
Pressure: 12 feet (3.6 meters) of head pressure.
Weight: About 10 pounds (4.5 kg) in CPVC, depending on pump- body length
Motor: Epoxy coated, 1/12th hp (60 watt), single phase, 3000 RPM, TEFC, thermally protected. Electrical cord is 10 feet (3 meters) long. When ordering, specify one of the following motors:
(1) 115 volt, 60 Hz, 2.3 A
(2) 230 volt, 50/60 Hz, 1.3 A

BX1200 Pump-Body Length
All Flo King pumps are manufactured in different pump-body lengths to accommodate the freeboard (distance from top of tank to solution surface) and, in many cases, tank depth. To ensure priming and proper operation, solution must be 1 inch (2.5 cm) or more above the Weep Hole on the BX1200 pump body. The Impeller is located just beneath the Weep Hole and must be submerged in solution for the pump to operate.

Specify length of pump body when ordering. If you are not sure which length is required, supply all of the information requested at this link and we will recommend a system.